Butikssida
Space Engineers
Alla Diskussioner Skärmbilder Konst Sändningar Filmer Workshop Nyheter Guider Recensioner

Space Engineers

Butikssida
Space Engineers >  Workshop > Spites workshop
26 betyg
ISL - Myxini Tunnel Miner MK3-AO 880
Beskrivning Diskussioner0 Kommentarer3 Ändringar
   
Utmärkelse
Favorit
Favoritmarkerad
Avfavoritmarkerad
Type: Blueprint
Taggar: ship, small_grid, safe
Filstorlek
Lades upp
Uppdaterades
4.005 MB
17 maj, 2020 @ 10:35
28 apr, 2021 @ 8:35
5 ändringsnotiser ( visa )
DLC som krävs
Denna artikel kräver all följande DLC
Space Engineers - Decorative Pack
Artiklar som krävs
Denna artikel kräver alla följande artiklar
Skapat av
Spite
Offline
Se alla 369 samlingar skapade av Spite och andra personer
2,131 Unika besökare
4,844 Nuvarande abonnemang
44 Nuvarande favoriter
Du behöver DLC för att kunna använda denna artikel.

Abonnera för att ladda ner
ISL - Myxini Tunnel Miner MK3-AO 880

I 3 samlingar av Spite
ISL - Small Grid Printable Ships (with Printer)
185 artiklar
ISL Shipyard
218 artiklar
ISL - Small Grid Miners
60 artiklar
Beskrivning
Purpose
A medium miner designed for tunneling horizontally or diagonally either manually or with the PAM autominer script.

The MK3 is available in all three thrust types, either as Agna (Basic Cockpit) or Myxini (industrial Cockpit) variants and features 4 connectors (allowing for varied docking options), a larger drill profile than the MK1 and MK2 Tunnel miners, and a stone ejection system.

The Hydrogen version can be used on moons but is not recommended for planets.

Features
Tools, Scripts & Weapons:
PAM Autominer script
Fancy Status Displays script
4 forward facing drills

Power:
7 Large Batteries

Movement & Control:
1 Cockpit
1 Remote Control
4 Gyroscopes
10 Large Atmospheric Thrusters
30 Small Atmospheric Thrusters

Cargo Space
4 Medium Cargo Containers
4 Connectors
4 Drills

Miscellaneous:
4 Cameras - Po, Sb, Rear, Underside
1 Ore Detector
1 Sensor (for use with PAM)
2 Spotlights
Repair Projector

This ship has an empty mass of 81341 kgs, and can move with a full cargo at a maximum tilt of 90 degrees below horizon, but cannot fly upside down.

All Programmable blocks are turned off in this blueprint and all toolbars are the same from the cockpit and remote control.

All ships in this set have a rear mounted Merge block and can be printed using a welder wall with one (large grid) piston.

Toolbars
Toolbar 1
1. Thrusters All On
2. Thrusters All Off
3. Thrusters Braking On
4. Thrusters Braking Off
5. Lights On/Off
6. Connectors Switch Lock
7. Camera Port
8. Camera Starboard
9.

Toolbar 2
1. Battery Discharge
2. Battery Recharge
3.
4. Camera Underside
5. Camera Rear
6. Drill Control
7. Drills On/Off
8. Ore Detector On/Off
9. Antenna Broadcast On/off

Toolbar 3
1. PB [PAM] "up"
2. PB [PAM] "down"
3. PB [PAM] "apply"
4. Ejector System On/Off
5. PB [PAM] "Align"
6. PB [PAM] "homepos"

Toolbar 6
1.
2.
3.
4.
5. Repair Projector On/Off
3 kommentarer
< >
omni 22 jul, 2023 @ 9:11 
so his problem might be caused by having thrusters on as when they are on they cause it to clang out or atleast that is what i have found when printing it
Spite  [skapare] 9 jan, 2021 @ 20:21 
Thanks GuitarEC, glad you like the design.

As for your printing problem, the welder wall is definitely big enough.

are you printing layer by layer? This can be done using butting for increasing and decreasing minimum distance on the piston. This has been the only reliable way for me.

Or are you letting the piston retract all the way in one go? No matter how slowly, this usually leaves out some blocks, especially in the more complex designs
GuitarEC 9 jan, 2021 @ 19:48 
I love the design, but it was a real bear to print for some reason - lots of blocks that didn't print, and I had to follow behind and manually weld things - sometimes having to grind out surface armor to get to inner areas (gyros, projector, etc). FYI - my printer is a 5x3 grid, piston travel is only 0.15 m/s.