Subscribe to download
[PC] MWMB-Skriptus

MWMB-Skriptus is designed for riding on terrain of medium to light complexity in planetary gravity and atmospheric conditions. MWMB-Skriptus is equipped with a full-service production facility, 3x3 welder wall, and a lifting platform for containing and transporting additinonal wheeled vehicles. MWMB-Skriptus can act as a mobile habitable base, providing it's protection with a built-in safe zone.

Specifications :

• Mass: 727 t
  
• PCU: 9536
  
• Working volume of cargo containers 1x: 875 kL
  
• Number of small containers: 2
  
• Number of large containers: 2
  
• Total volume of hydrogen tanks: 15 ML
  
• Number of large hydrogen tanks: 1
  
• Number of O2-H2 generators:
  
• Number of batteries: 4
  
• Number of H2 engines: 2
  
• Number of programmable blocks: 2
  
• Number of Welders: 5

---

User can operate the multifunctional elevator from 4 control points:

• main cockpit, located at the head end of the hull.
  
• secondary cockpit, located in the near of the welder wall at the rear end of the hull
  
• button panel, located on the parking platfor of the lifting platform.
  
• button panel, located on the rear bottom part of bottom magnetic plate.

Also, through the cockpits it is possible to monitor the actions being performed.

At each control point, the lifting platform can be lowered and raised using the following commands

• Lpos1 - lower lifting platform
  
• Lpos2 - raise lifting platform

Attention! Before operating the lifting platform, the user must bring the suspension into a certain position by means of the following command :WheelDow (lower the wheels). Driving with the elevator lowered is strictly prohibited due to the operation of the magnetic plates of the lower part of the parking pad.

---

The lifting platform acts as a seeding for the assembly projection and is also used to pull the grid from the welding wall.

Attention! When starting work with the seeding projector, the user must make sure that there are no other vehicles in the elevator parking lot or they must be securely fastened to the connectors.
It is strictly forbidden to retract the lifting platform piston with the welded grid connected to the seeding hinge beam!
It is strictly forbidden to change the position of the beam of seeding hinge if any vehciles are connected to the lifting platform!
It is strictly forbidden to cange the position of the lifting platform with welded grid connected to the seeding hinge beam!
Be careful when the welders are on and do not enter the area where they are working!
After finishing work with the seeding projector, make sure that the seeding hinge beam is moved to its original position (parallel to the surface of the welder wall)

---

EDB Anker is not liable for potenital damade to the user's tangible property in cases of breach of safety of safety and operation of the lifting platform.

---

EDB Anker notifies the User of the absolute refusal to pay the insurance indemnity due to gross violations of safety requirements and improper operation of the MWMB-Skriptus.

---

The seeding projector is operated from the secondary cockpit using the following sequence of commands:

• bring lifting platform in marching position [Lpos2]
  
• turn the autolock off on the magnetic plate of the lifting platform's stopper
  
• unblocks the magnetic plate of lifting patform's stopper
  
• Extend the lifting platform's piston
  
• turn the projector of seeding hinge on (orange)
  
• turn the hinge lock of the seeding hinge off
  
• align the hinge of the seeding hinge projector perpendicular to the welder wall
  
• adjust the position of the seeding projection so that the rover is positioned with the wheels downwards or with the wheels towards the welder wall.
  
• connect the beam of the seeding hinge to the projection
  
• retract the piston
  
• turn the welders on
  
• set the required piston extension speed via the control panel
  
• wait until the grid is fully welded and the piston is fully extended
  
• wait until the assembled grid is minimally charged and disconnect the assembled grid

When the projection is positioned with the wheels facing the welder wall, the elevator can be moved to the vertical position and back again if necessary using the RotorP1 (vertical position) RotorP2 (original position) commands.

---

QAB

Page 1

1. camera front view
   
2. camera rear 1 view
   
3. camera rear 2 view
   
4. spotlight control
   
5. beacon on\off
   
6. antenna on\off
   
7. thrust on\off
   
8. wheel group increase speed limit
   
9. wheel group decrease speed limit

Page 2

1. camera rear 1 view
   
2. camera rear 2 view
   
3. PB_EA raise wheels
   
4. PB_EA lower wheels
   
5. _
   
6. PB_EA lower lifting platform
   
7. PB_EA raise lifting platform

Page 3

1. camera front view
   
2. camera rear 1 view
   
3. camera rear 2 view
   
4. light of bottom connector on/off
   
5. connector switch lock
   
6. H2 engine on\off
   
7. batteries charge on\off
   
8. O2/H2 generator on\off
   
9. H2 tank stockpile on\off

Страница 4

1. PB_EA raise wheels
   
2. PB_EA lower wheels
   
3. camera bottom view
   
4. magnetic plate switch lock
   
5. _
   
6. PB_EA fully raise the wheels
   
7. PB_EA fully lower the wheels

Used Scripts
В MWMB-Skriptus uses these scripts:
Easy Automation
WMI Radar by Whiplash141

---

EDB Anker informs the user that MWMB-Skriptus is primarily a design work, as well as a development of the concept of a multifunctional lifting platform.