Suscríbete para descargar
Oblivion Bubble Ship

The Oblivion Bubble Ship is a planetary ship designed for scouting ore deposits and potential sites for new facilities. The Oblivion Bubble Ship is a rough facsimile of the bubble ship from the sci-fi movie Oblivion, but without the guns. It uses the same vectored-thrust approach for flight, although the tail uses opposing thrusters rather than a rotor. The two doors are hinged for easy boarding access; the cockpit is not, therefore, airtight. Power is supplied by batteries, and a connector is included to facilitate the battery charging process.

A single mod is used for the flight seats to enable close, side-by-side placement:
  - 1x1x1 Small Control Seat Mod by Ace
    (https://steamcommunity.com/sharedfiles/filedetails/?id=1904327095)

A vectored-thrust control script is included in the programmable block:
  - Vector Thrust 2 by Vermillion
    (https://steamcommunity.com/sharedfiles/filedetails/?id=1210578673)

SURVIVAL READY AND PROJECTOR BUILDABLE!

NOTE: The two vector thruster rotors are locked, mostly as an aid for building in survival; unlock the rotors before first flight.

STATISTICS
  - Blocks: 438
  - PCUs: 2,916
  - L × W × H: 13m × 7½m × 5½m
  - Empty Mass: 25 tons

CONTROLS 1 FOR BOTH CONTROL SEATS
{1} Camera Front View
{2} Spotlights On/Off
{3} Doors Open/Close
{4} Magnetic Pads Autolock On/Off
{5} Magnetic Pads Switch Lock
{6} Camera Down View
{7} Connector Lock/Unlock
{8} Systems Off
{9} Systems On

CONTROLS 2 FOR BOTH CONTROL SEATS
{1} Batteries Auto/Recharge
{2} ---
{3} Marker Lights On/Off
{4} Door Lights On/Off
{5} ---
{6} Ore Detector On/Off
{7} Antenna On/off
{8} ---
{9} ---

INSTRUCTIONS FOR BUILDING WITH PROJECTORS
Because this blueprint uses two rotor and two hinge sub-grids, building with projectors in survival mode may be accomplished relatively easily.
1.  Build the ship's main structure as follows:
    a.  Install a rotor frame, remove the large rotor head, and replace with a small rotor head; lock the rotor.
    b.  Install five (or more) armor blocks above the small rotor head to allow adequate clearance for building the ship; install a projector atop the uppermost armor block with the top up (cross) per the above picture.
    c.  Load the ship's blueprint into the projector and check the box entitled "Keep Projection". (Note that SE will whine that it doesn't support multiple grids; ignore the warning by just clicking "OK".)
    d.  Build the main structure.
2.  Once the main structure is built, the two vectored thruster assemblies are installed using local projectors as follows:
    a.  Install a projector on the left rotor head and rename the projector to be "OBS - Projector Thruster Left"; orient the projector with the front out (single vertical line) and top up (cross) per the above picture.
    b.  Load the OBS Thruster Left blueprint into the projector and check the box entitled "Keep Projection": https://steamcommunity.com/sharedfiles/filedetails/?id=2775757855
    c.  Build the left thruster assembly (4 blocks, total).
    d.  Install a projector on the right rotor head and rename the projector to be "OBS - Projector Thruster Right"; orient the projector with the front out (single vertical line) and top up (cross).
    e.  Load the OBS Thruster Right blueprint into the projector and check the box entitled "Keep Projection": https://steamcommunity.com/sharedfiles/filedetails/?id=2775757959
    f.  Build the right thruster assembly (4 blocks, total).
3.  Once the main structure and thruster sub-grids are built, the two hinged door assemblies are installed using local projectors as follows:
    a.  Install a projector on the left door hinge and rename the projector to be "OBS - Projector Door Left"; orient the projector with the front forward (single vertical line) and top up (cross) per the above picture.
    b.  Load the OBS Door Left blueprint into the projector and check the box entitled "Keep Projection": https://steamcommunity.com/sharedfiles/filedetails/?id=2775758076
    c.  Build the left door assembly (18 blocks, total).
    d.  Go to the control menu from any access point, select "OBS - Button Panel Door Left", and click on "Setup actions"; assign "OBS - Timer Block Doors 1" to the only action slot, and specify "Trigger now". If desired, click on "Button 1" and change the button name to "OPEN/CLOSE DOORS".
    e.  Install a projector on the right door hinge head and rename the projector to be "OBS - Projector Door Right"; orient the projector with the front forward (single vertical line) and top up (cross).
    f.  Load the OBS Door Right blueprint into the projector and check the box entitled "Keep Projection": https://steamcommunity.com/sharedfiles/filedetails/?id=2775758170
    g.  Build the right door assembly (18 blocks, total).
    h.  Go to the control menu from any access point, select "OBS - Button Panel Door Right", and click on "Setup actions"; assign "OBS - Timer Block Doors 1" to the only action slot, and specify "Trigger now". If desired, click on "Button 1" and change the button name to "OPEN/CLOSE DOORS".
4.  Enter either control seat and press {9} to turn on systems and thrusters; the doors will automatically close.
5.  Press {3} to open the doors.
6.  Remove the blocks and rotor from beneath the ship; the ship should hover, but may move forward slowly.
7.  Re-enter the control seat and press {3} to close the doors.
8.  Move the ship forward/backward and/or laterally to a level location and land the ship; press {8} to put all systems into standby mode.
9.  Press {i} to go to the control menu and unlock the two thruster rotors.
10. Now you're ready to fly away into oblivion!

REQUIRED PARTS FOR BUILDING THIS SHIP IN SURVIVAL
  - 661 Steel Plates
  - 24 Metal Grids
  - 63 Interior Plates
  - 443 Construction Components
  - 355 Motors
  - 40 Large Steel Tubes
  - 9 Small Steel Tubes
  - 151 Computers
  - 8 Displays
  - 87 Girders
  - 189 Bulletproof Glass
  - 104 Power Cells
  - 1 Detector Components
  - 4 Radio-Communication Components