Stormworks: Build and Rescue

Stormworks: Build and Rescue

Няма достатъчно оценки
JR Freight EF210 Electric Locomotive
   
Награда
Добавяне към любими
В любими
Премахване от любими
Тагове: v1.5.3
Размер на файла
Публикуван на
Обновен на
1.466 MB
30 ян. 2021 в 3:49
4 юли 2022 в 5:29
7 бележки за промени ( преглед )

Абониране, за да се свали
JR Freight EF210 Electric Locomotive

Описание
This is the main electric locomotive of JR Freight.

Hotkeys
  • w/s:One handle operation (w=acceleration/s=deceleration)
  • u/d:Clutch (u=pressure up/d=pressure down)
  • 1:Emergency Brake
  • 2:Close the cab doors
  • 3:Front Lights
  • 4:Dimmin Front Lights
  • 5:Toggle Signal
  • 6:Horn(Only when Infinite Electric mode is disabled)

Operation Manual
Starting procedure
  1. Turn the key switch on the driver's cab to ON. If the key on the opposite cab is enabled, operate the key twice.
  2. Operate the pantograph button "Pantograph xx" on the cab.
    The pantograph will go up and the power generator will activate. Also, the motor will be able to start.
  3. Operate the "Motor 1" to "Motor 3" buttons on the cab to start the motor.
  4. Accelerate by pressing the "w" key.
    In case of wheel slipping, use the clutch operation (u/d) together. In most cases, loosening the clutch to the red line on the monitor will release the wheel slipping.
  5. Decelerate by pressing the "s" key.

High-Speed Operation
  • When the "Aux Blower" button on the cab is pressed while the motor is running, the additional ducted fan is activated, allowing for high speed running(+10-20km/h). Since it uses a lot of power, it is recommended to use it for temporary acceleration.
  • The maximum speed is 120km/h for a single machine, and about 135km/h when the ducted fan is activated. If the "Power Mode" button in the machine room is turned off, the machine can run at high speed(230-250km/h).

Connect to other trains
Supports SW-TCS[wikiwiki.jp].
  • In the initial state, the coupler is OFF. Please turn on the "Front Connector" or "Rear Connector" button to activate the coupler.
  • There is a hidden button for the Uncoupling Lever on the right side of the coupler. When decoupling outside the train, the coupler can be released without returning to the cab.

Multiple unit control
Supports R-BUS CAT2[wikiwiki.jp]
  • Use the R-BUS signal cutoff switch(Cut-Off xx R-BUS) when not sending R-BUS control signals such as towing a broken-down vehicle.
  • If it is an helper engine, perform only steps 2 and 3 of the starting procedure. The status can be checked with the indicator behind the cab. If you are an helper engine, you cannot use the monitor.
  • If it is to be an helper engine for another user's locomotive, turn off the "Acceralation Control" button in the machine room if necessary.
    The acceleration adjustment mechanism is disabled, and the input value of R-BUS is directly transmitted to the motor.

Train Horn
Added train horn using siren and voltage control(since update on March/12/2022)
When the Infinite Electric mode is enabled, the train horn will sound constantly. Please turn off the "Activate Horn" on the front side of the machine room.

Used Workshop Items

Re-uploading (including modification) of this vehicle is prohibited.

This document is a machine translation of a Japanese document by DeepL.
8 коментара
Mr. T 25 окт. 2022 в 10:42 
Really good.
cuh-ku  [автор] 19 окт. 2021 в 9:42 
>azuki3741
すみません、"Front Connector"もしくは"Rear Connector"ボタンが正しいです。
正面にある2つのDialの左にあります。

本文を修正しました。
yuzulemon 17 окт. 2021 в 22:24 
Connector xx"のボタンの位置が分からないです、出来れば場所を教えてください.
JamieTheGreat 25 февр. 2021 в 3:47 
never mind, i pressed it haha
JamieTheGreat 25 февр. 2021 в 3:42 
Great creation, proper decent train! only question, what does the fusee do?
NotPokémon 5 февр. 2021 в 12:42 
I LOVE THIS. it runs so smooth, it has indicaters for weelslip, when the pantagraph is down the power dont work, just amazing
北上 30 ян. 2021 в 7:31 
とても面白くて気に入っています
個人的に速度を調べてみて重連の時
最高時速が大体110㎞/hになりました
FredMeisterParry 30 ян. 2021 в 4:55 
Wow. Just wow