Jaguar-Class Missile Corvette Guide

A guide on how to use the Jaguar-Class Missile Corvette and it's missile system.

How to start the engines.

- Enter the bridge
- Make sure your breakers are on
- Go to the bottom left control panel (notable for being full of dials)
- Press "Engine Compressor" (Far left button)
- Press "Electric Starter Motor" next to it
- Increase engine throttle to 30%
- Increase both "Overall clutch" and "Engine clutch" to 100%
- Increase engine throttle to full after you've started moving.

Driving the ship.

General Driving
- Go to captains seat (top left seat)
- Once again similar to the Type 23, there's a 15 degree steering limiter to prevent capsizing as well as keep the missiles in their "baskets".
- Also similarly to the Type 23, keep your throttle low when you are FACING AT or AWAY from the waves, as it also tends to jump. When you have your sides to the waves you are relatively safe contrary to what sailors would tell you usually!

Moving at a minimal amount
- Decrease your ENGINE clutch to 0% (middle throttle)
- Increase your OVERALL clutch to 100% (left throttle)
- Sit in the captains seat (top left), use WASD for electric motor control over the props.

- For FULL clutch, decrease OVERALL clutch to 0%

Using the Sea Leopard Launch System.

- Before anything, make sure the missile breaker (bridge) is on.
- DO NOT TOUCH MISSILE RACK OVERRIDE UNLESS NECESSARY. FURTHER EXPLAINED BELOW.
- THEY ARE LASER GUIDED MISSILES, NOT GPS/RADAR GUIDED.

Activating the launch system
- Turn on "Monitor 1" and "Monitor 2" (small buttons vertically stacked)
- Turn on your laser (big button below monitor buttons)
- Use the left and right arrow to point your launcher in the general direction of the target
- Use WASD to point your laser designator towards the target (optimal conditions are as less waves as possible, you will still need to use WASD to keep the laser on target as it is very sensitive to the boats motion)
- Use the arrow buttons on the panel for zoom (or the up/down arrow keys)
- For targets of roughly 1KM set your Launcher Rail Pitch to roughly 0.80

Firing the Sea Leopard
- Press "Load missile"
- Do NOT touch any camera controls if it does appear to move, that's the launcher itself moving)
- Wait for the green indicator to say "loaded", after that, turn off "load missile".
- Wait until your launcher resets back to its position you chose.
- Hold your laser on the target via WASD with support from the stabilizer.
- Press "Fire".
- To load again, do the above once more.

What the mysterious "Missile rack override" button does and the temptation to push it
- When the rotary rack desyncs, as in it does NOT connect properly to the grippers, this will result in a failed load.
- What missile rack override does is manually overrides the rotor system so you can move it into a place where it will align and connect to the grippers.
- To use it, press the button, use your throttle to align the rotary rack to the grippers, once aligned, turn off the override button.
- Results vary between how much the rack has desynced, which shouldn't happen in the first place.

Deploying the rear RHIB

To exit the corvette:
- Sit in the RHIB, turn on your engine, throttle up.
- Press "5" to disconnect the RHIB connector from the corvette's connector.
- Press "Doors", top right.
- Press the push button next to it, this will extend the corvette's connector.
- Use WASD to use the RHIBs electric motor to reverse you out.
To enter the corvette:
- Approach slowly towards the centerline connector on the corvette.
- Press "5".
- Connect to the connector, the corvette will pull you in.
- Press "doors" to close the doors.

[76561198811853833]

thank biggie cheese

[Biggie Cheese]

Yes

[76561198811853833]

is it advanced mode