Infinity Nikki

Infinity Nikki

View Stats:
Steam deck performance?
So i installed it and once the cutscene was over i was at 20 fps and lower is the game not optomized or am i using the wrong proton?
< >
Showing 1-14 of 14 comments
Same here. I tried lowering quality settings but there really isn’t much left to change.
Kazumi Apr 29 @ 11:41am 
Originally posted by Kronusdark:
Same here. I tried lowering quality settings but there really isn’t much left to change.
ahhh okay i'm not sure if its bc of the steam version but i've seen ppl play it nicely.
stinky Apr 29 @ 1:32pm 
I really want help getting it to run nicely. It’s literally unplayable with the fps and I’m sad I have to have all graphics on the lowest setting.
After getting out of the new season introduction area, the framerate improves but yeah it's rough on steam deck so far.
Biscuit Apr 30 @ 8:38pm 
It is just rough in the new opening area for the game. Once you get out of that first area it is much better.
The graphics and lag are awful, even more so if connected to a television via HDMI. I really hope they work on this.
elimoshe May 2 @ 10:41pm 
wat for me to sayyy im installing
ShinyaKami May 3 @ 5:12am 
Tested on a SteamDeck LCD.
the game is unstable to say the least but I manage to get a decent performance with the following settings.

Before you open the game do this:
  • Go to game Properties>Compatibility>Force the use of a specific compatibility tool>Proton Hotfix
Now open the game and press the '...' button then Go to the performance tab and enable "Use per-game profile" and limit the frame rate to 30fps.
    As for in-game settings
  • Frame rate limit = Unlimited.
  • Vertical Sync = Off.
  • Dynamic Res = Off.
  • Super Res Method = TSR>Quality and medium.
  • Graphics Details = Go all medium
    except for Texture Quality = High.
  • Motion Blur = Off.
    Leave everyting else to default.
You might encounter some disconnection issues, other than that I really hope this helps (⁠◍⁠•⁠ᴗ⁠•⁠◍⁠)
Last edited by ShinyaKami; May 3 @ 5:19am
Xenthoxin May 10 @ 11:42pm 
I was getting 60fps easily launching it as a "non steam" game before this most recent steam deck update, but now I just get a driver error when trying to launch the game (steam and non-steam)
embreon May 13 @ 3:12pm 
Originally posted by ShinyaKami:
Tested on a SteamDeck LCD.
the game is unstable to say the least but I manage to get a decent performance with the following settings.

Before you open the game do this:
  • Go to game Properties>Compatibility>Force the use of a specific compatibility tool>Proton Hotfix
Now open the game and press the '...' button then Go to the performance tab and enable "Use per-game profile" and limit the frame rate to 30fps.
    As for in-game settings
  • Frame rate limit = Unlimited.
  • Vertical Sync = Off.
  • Dynamic Res = Off.
  • Super Res Method = TSR>Quality and medium.
  • Graphics Details = Go all medium
    except for Texture Quality = High.
  • Motion Blur = Off.
    Leave everyting else to default.
You might encounter some disconnection issues, other than that I really hope this helps (⁠◍⁠•⁠ᴗ⁠•⁠◍⁠)

Wow, thank you. I've been struggling with a lot of motion blur (can't even use the camera on steam deck) and weirdly spotty graphics because by default the game just sets everything very low. Instant improvement with these settings.
lilac May 13 @ 8:46pm 
the performance isnt even good on PS5 i wouldnt even try playing this on the deck tbh.
gwwak May 14 @ 3:45pm 
Performance is acceptable on the ROG Ally. 1080p medium, get around 30-45 fps.
I have a Steam Deck OLED.
My settings are higher, but not all maxed.
I've been playing on the Limited Edition Steam Deck with no significant issues. I had the non Steam version installed on the Deck earlier and it was also running fine.
Last edited by burumanet; May 16 @ 3:43pm
< >
Showing 1-14 of 14 comments
Per page: 1530 50