AMD Software and 2024 not playing together?

[MugHug]

Wonder if anyone experience the following or knows (not guessing) why it is happening?

It seem that while AMD Software꞉ Adrenalin Edition identifies the MSFS 2024 installation and can even start the sim, it does not or cannot apply the 'Gaming graphics' setting that you can setup. No problem in MSFS 2020.

I realize that MSFS 2024 comes with FSR 2, so there maybe no need for 'Super Resolution'. But one cannot even disable FSR 2 in-game and use the 'Super Resolution' setting in the AMD Software. VSync was off and set resolution was one down from monitor resolution.

And AMD Fluid Motions 2 does not seem to work in MSFS 2024.

I do notice that when I enable FSR 2 in-game that my FPS seems to increase slightly compared to having it off.

But the application 'Lossless Scaling' frame generation does seem to work fine and generates nearly double the FPS.

Anyone find the same or know what is going on?

[B. Schroeder]

For me too.

[MugHug]

The more I think of it, the more I feel it was intentional setup this way for AMD cards.

We still get 'up-scaling technology' via the inbuilt FSR 2, plus I observe that when the FSR 2 is enabled we also get a small 'semi-frame generation' boost in FPS.

Do you see a slight increase in FPS when you use FSR 3?

[B. Schroeder]

So everything works for me now. Even Fluid Motion Frames 2. I now have an average of 100 FPS with my 7800 XT

[MugHug]

Schroeder🅱님이 먼저 게시:

So everything works for me now. Even Fluid Motion Frames 2. I now have an average of 100 FPS with my 7800 XT

Does the AMD Software actually show a green checkmark for frame generation, does Super Resolution work and and what driver version?

I am using 24.10.1 here and no new patches for MSFS.

When FSR 2 is turned on and working in-game, the AMD Software just tells me frame generation is not possible (from the driver side). But FSR 2 does not have it's own frame generation.

So not sure where you are getting your frame generation from.

[B. Schroeder]

Yes, the AMD software shows a green check mark for frame generation, super resolution also works.

I'm using the 24.20.19.05 beta driver here

V-Sync obviously has to be off in the game, otherwise there can be problems.

[B. Schroeder]

The Link for 24.20.19.05:

https://www.amd.com/en/resources/support-articles/release-notes/RN-RAD-WIN-24-20-19-05.html

[MugHug]

Thanks for info. Will install them to test. :)

[MugHug]

Exactly the same with the suggested drivers. Tried all combinations of internal and game settings, etc. and nothing.

[B. Schroeder]

Hm. Everything works fine for me. Fluid Motion 2 and Super Resolution all work fine. What could it be?

[MugHug]

Going to remove and reinstall the AMD software, etc. Noticed new issues with both X-Plane 11 and 12.

[B. Schroeder]

Problem solved with lastest driver 24.12.

[MugHug]

Installed 24.12 and still same issue. Weird.

[B. Schroeder]

Really mysterious

[MugHug]

Yep.

Otherwise it all works sweet and if needed I use Lossless Scaling.

AMD Fluid Motion Frames 2 tells me 'Not compatible with the game's display mode.' The mode in use is Full Screen 2024x1296 on a 3440x1440 monitor using the built-in FSR 2 and V-Sync off in-game and in AMD software.

Straight 3440x1440 Full screen and no vsync is the same. Basically all combinations are the same - no AFMF. And nothing in the Community folder does not help.

Have noticed when MSFS2024 is booting that AFMF does kick in for a split-second and then goes to the above error message,

Seems to be the only game with this issue.

[B. Schroeder]

I successfully use AMD Fluid Motion Frames 2 on a 3440 x 1440 monitor with V-Sync turned off in the game.

No problems for me.

It's quite a mysterious thing.

RX 7800 XT with 5800X3D and 64GB DDR4, Windows 11