Too much of AI traffic

[warmate]

Maybe someone already had this issue. I'm flying with FSRealistic, FSTSL and Beyond ATC. Every time I see a lot of additional traffic (with "blank" liveries), planes one over another at the airports, a lot of traffic in the air which are NOT "visible" by BeyondATC, so it allows me to fly though them etc. Before I will start digging deeper - anyone had this kind of problem? As far as I remember, everything was fine about 2 months ago, now I started flying once again and its pretty annoying

[Twelvefield]

Double-check that AI traffic is turned off completely in MSFS. It's possible that an update turned those things back on for you. Every update, it's mandatory to check all of your settings, as often they will be reverted to defaults.

[Mightylink]

Airport Traffic spawns a lot of fake parked planes that just eat up performance and give you nowhere to park, I turned that off and only kept Live Traffic On which still shows a few planes at most airports.

[Twelvefield]

Publicado originalmente por Mightylink:

Airport Traffic spawns a lot of fake parked planes that just eat up performance and give you nowhere to park, I turned that off and only kept Live Traffic On which still shows a few planes at most airports.

BATC does its own traffic injection, though. You have to turn off all the AI planes, including scenery planes, otherwise you get duplicates.

[Ska Dee]

Publicado originalmente por Twelvefield:

BATC does its own traffic injection, though. You have to turn off all the AI planes, including scenery planes, otherwise you get duplicates.

I don't think you Need to have BATC for that.
They re-using traffic injector from FlyByWire installer, free software.

[warmate]

Ok, I turned off AI planes in MSFS and now I'm using only FSRealistic and BATC. AI traffic number is lower, but I still have random aircrafts (with generic liveries) placed all over and its not BATC (when Im turning off AI traffic on BATC I can see that a lot of airplanes dissapearing, but not all of them). Any ideas whats going on?
BTW, I have also GSX installed and running, but I think it does not have AI traffic built in

[ждун]

Publicado originalmente por warmate:

Ok, I turned off AI planes in MSFS and now I'm using only FSRealistic and BATC. AI traffic number is lower, but I still have random aircrafts (with generic liveries) placed all over and its not BATC (when Im turning off AI traffic on BATC I can see that a lot of airplanes dissapearing, but not all of them). Any ideas whats going on?
BTW, I have also GSX installed and running, but I think it does not have AI traffic built in

also disable airport traffic. The amount of parked planes is a separate setting. If you are using 3rd party traffic tools, they will handle both ground and air traffic and usually you have to disable default ground and air traffic in msfs.

[warmate]

How to disable airport traffic?

[Eva]

Under graphics settings there is a airport traffic setting near the bottom. Turn airport traffic to off.

[warmate]

Thank you very much!

[Eva]

Glad to help. Hope it cleans things up. :)

[Twelvefield]

Publicado originalmente por Ska Dee:

Publicado originalmente por Twelvefield:

BATC does its own traffic injection, though. You have to turn off all the AI planes, including scenery planes, otherwise you get duplicates.

I don't think you Need to have BATC for that.
They re-using traffic injector from FlyByWire installer, free software.

The only injector that you run on BATC is the BATC injector, which automatically is used exclusively by BATC. That is it. Nothing else. You can use FSLTL models, AIG models, FSTraffic models, and/or FS24 GA models in any combination and order.

Running anything else besides BATC will cause you to have duplicated planes. You do not install the FBW injector, just the model file. You do not allow MSFS to inject planes, you turn AI aircraft and scenery aircraft to 0%.