Controls not working on tractor

[Jeff]

Well some of them do, but the horn doesn't honk (pressed the zero and the letter O).

Also trying to lower the front hydraulics to pick up a weight. In Farming Simulator 13 I would press the "G" to switch from the back to the front hydraulics. Then press the "V" to raise or lower.

[grayraanger11]

the game came out last year there is going to be bugs

[HurtfulPlayer97]

Did you install Mods? Some Mods reassign keys. Check you keybindings.

[Jeff]

No mods being run. Just a simple game, but unless I can figure out these controls (default key bindings in options not working either), this game was a waste of $43 (premium version).

[MYSTEPMOMISSTUCK]

i now cannot steer or use gas pedal

[bnorberger]

I don't know whats wrong with your horn but to attach your weight or any other implement you should just be able to drive or back up to it and press Q to attach. Then after it's attached you can press G to select your implement and move it up and down with V if its attached to the 3 point hitch.

[ShutEye_DK]

OP, this is a problem on your end. Millions can play this game just fine.

Remember this is NOT FS13. Read the controls that shows in the F1 help window.
Maybe something changed.

[Liquid Todd / Slash]

Originally posted by ShutEye_DK:

OP, this is a problem on your end. Millions can play this game just fine.

Remember this is NOT FS13. Read the controls that shows in the F1 help window.
Maybe something changed.

I very much doubt you can rule out the problem being outside of the OP's control with the little information that you have been given. There might be some sort of hardware/software conflict which could be the problem.

I would also like to know where these "millions" of players are? I mean if there were "millions" then all the servers would be rammed. Lets go for 10's of 1000s shall we? Max.

[ShutEye_DK]

Originally posted by Liquid Todd / Slash:

Originally posted by ShutEye_DK:

OP, this is a problem on your end. Millions can play this game just fine.

Remember this is NOT FS13. Read the controls that shows in the F1 help window.
Maybe something changed.

I very much doubt you can rule out the problem being outside of the OP's control with the little information that you have been given. There might be some sort of hardware/software conflict which could be the problem.

I would also like to know where these "millions" of players are? I mean if there were "millions" then all the servers would be rammed. Lets go for 10's of 1000s shall we? Max.

Millions. Not online. Just playing through the times. I'm not talking about concurrent players.

And it IS on OP's end. As you actually write yourself.

[Jeff]

Originally posted by bnorberger:

I don't know whats wrong with your horn but to attach your weight or any other implement you should just be able to drive or back up to it and press Q to attach. Then after it's attached you can press G to select your implement and move it up and down with V if its attached to the 3 point hitch.

The weight I was trying to pick up was at the front of the tractor. There should be a way to switch to the front three point hitch to pick up the weight.

[ShutEye_DK]

Originally posted by Jeff:

Originally posted by bnorberger:

I don't know whats wrong with your horn but to attach your weight or any other implement you should just be able to drive or back up to it and press Q to attach. Then after it's attached you can press G to select your implement and move it up and down with V if its attached to the 3 point hitch.

The weight I was trying to pick up was at the front of the tractor. There should be a way to switch to the front three point hitch to pick up the weight.

No need to. If you approach the weight from the correct side, just attatch it.
"Q" is the default IIRC (I play with a controller).
Then you can switch to it. You can only switch to attatched tools, not the attatcher itself.

[Jeff]

Q disconnects and V lower/raises -- I understand that. But how do I use the same commands at the front of the tractor??


I looked in the options and yes, The "G" key is still used to switch between implements (it just doesn't work). I did get the "0" horn to work. It's just so incredibly quiet I didn't hear it before.

[ShutEye_DK]

Just position a free attacher at a tool. Text will show up with the tool's name when it can connect. Hit Q.

An ATTACHER is not an implement. You CANNOT switch to an empty attacher.
When a tool is attached, just use G to switch to it.

[Jeff]

Originally posted by ShutEye_DK:

Just position a free attacher at a tool. Text will show up with the tool's name when it can connect. Hit Q.

An ATTACHER is not an implement. You CANNOT switch to an empty attacher.
When a tool is attached, just use G to switch to it.

Thanks for this reply. After I tried it on the "weight", I found that it could not be picked up by any tractor front or rear, but other weights could (the weight is defective).

[Jeff]

I deleted that save and started over -- it worked this time (only delayed me a week :)

[ShutEye_DK]

Good to hear :)