Todas as discussões > Fóruns Steam > Hardware and Operating Systems > Detalhes do tópico
p0mpous 21/set./2017 às 10:32
I7 4790k overclock.
what is a good voltage for a 4.8ghz OC, im thinking about having it about 1.260, does anyone else have this CPU with a similar OC.
< >
Exibindo comentários 1–15 de 44
Omega 21/set./2017 às 10:33 
You can safely go up to (and even slightly over) 1,3v.
#1
p0mpous 21/set./2017 às 10:35 
Escrito originalmente por Omega:
You can safely go up to (and even slightly over) 1,3v.
The mobos overclocking software tried to det it to 1.5v earlier.
Última edição por p0mpous; 21/set./2017 às 10:35
#2
Omega 21/set./2017 às 10:36 
Escrito originalmente por Sir Det Mist:
Escrito originalmente por Omega:
You can safely go up to (and even slightly over) 1,3v.
The mobos overclocking software tried to det it to 1.5v earlier.
Auto OCs always overvolt.
#3
⛧EyMi Mayhem⛧ 21/set./2017 às 10:37 
Do oc via bios...
#4
p0mpous 21/set./2017 às 10:38 
Escrito originalmente por ⛧EyMi Mayhem⛧:
Do oc via bios...
Im using the software from desktop, but it controls the bios but it wont apply on boot so it wont go wrong.
#5
Omega 21/set./2017 às 10:41 
Escrito originalmente por Sir Det Mist:
Escrito originalmente por ⛧EyMi Mayhem⛧:
Do oc via bios...
Im using the software from desktop, but it controls the bios but it wont apply on boot so it wont go wrong.
Always OC via BIOS.

If the OC is bad and the PC does not post reset the BIOS by pulling the CMOS battery for a couple of minutes.
#6
p0mpous 21/set./2017 às 10:47 
Escrito originalmente por Omega:
Escrito originalmente por Sir Det Mist:
Im using the software from desktop, but it controls the bios but it wont apply on boot so it wont go wrong.
Always OC via BIOS.

If the OC is bad and the PC does not post reset the BIOS by pulling the CMOS battery for a couple of minutes.
Whats the difference with this it isnt applied upon start so if it goes wrong it wont be applied on restart so it just boots with default settings.

Im looking in CPU-Z its using all the settings i have set its at 4.8GHZ, its only at about 75c, its at 1.265v
Última edição por p0mpous; 21/set./2017 às 10:48
#7
Omega 21/set./2017 às 10:49 
That is the issue. It doesn't auto apply on post. It will have to be applied while the OS is running.

Escrito originalmente por Sir Det Mist:
Im looking in CPU-Z its using all the settings i have set its at 4.8GHZ, its only at about 75c, its at 1.265v
Go ahead and run Prime95 for 24 hours then.
Última edição por Omega; 21/set./2017 às 10:49
#8
p0mpous 21/set./2017 às 10:52 
Escrito originalmente por Omega:
That is the issue. It doesn't auto apply on post. It will have to be applied while the OS is running.

Escrito originalmente por Sir Det Mist:
Im looking in CPU-Z its using all the settings i have set its at 4.8GHZ, its only at about 75c, its at 1.265v
Go ahead and run Prime95 for 24 hours then.
i normally just try through general use and CPU-Z, ive been at 4.7ghz for about 2 months.
#9
Omega 21/set./2017 às 10:53 
Escrito originalmente por Sir Det Mist:
Escrito originalmente por Omega:
That is the issue. It doesn't auto apply on post. It will have to be applied while the OS is running.


Go ahead and run Prime95 for 24 hours then.
i normally just try through general use and CPU-Z, ive been at 4.7ghz for about 2 months.
CPU-z only puts a very light load on the CPU. 75c with CPU-z = 100c with Prime95.
Última edição por Omega; 21/set./2017 às 10:53
#10
p0mpous 21/set./2017 às 10:54 
Escrito originalmente por Omega:
Escrito originalmente por Sir Det Mist:
i normally just try through general use and CPU-Z, ive been at 4.7ghz for about 2 months.
CPU-z only puts a very light load on the CPU. 75c with CPU-z = 100c Prime95. [/quoteI only play games i dont put it under massive loads.
#11
Omega 21/set./2017 às 10:56 
Still you need to test the OC stability. CPU-z is pretty bad for stability testing.
Última edição por Omega; 21/set./2017 às 10:56
#12
p0mpous 21/set./2017 às 11:07 
Escrito originalmente por Omega:
Still you need to test the OC stability. CPU-z is pretty bad for stability testing.
But prime 95 will generate far more heat then anything i do from day to day, so it kinda seems superfluous
#13
Omega 21/set./2017 às 11:11 
Escrito originalmente por Sir Det Mist:
Escrito originalmente por Omega:
Still you need to test the OC stability. CPU-z is pretty bad for stability testing.
But prime 95 will generate far more heat then anything i do from day to day, so it kinda seems superfluous
Stabilaty tesing isn't about heat. It's about testing if the OC is stable or not. You will get random BSODs if the OC is not stable. Prime95 and AIDA64 are the easiest ways to check for stabilaty due the the amount of stress they put on the system.

Why prime95??
For examply: If I increase the overclock on my rig by 100mhz the PC will appear to run fine on the desktop but once I run Prime95 it will BSOD withing a few secs - 1 minute. Meaning it's running unstable.
#14
p0mpous 21/set./2017 às 11:12 
Escrito originalmente por Omega:
Escrito originalmente por Sir Det Mist:
But prime 95 will generate far more heat then anything i do from day to day, so it kinda seems superfluous
Stabilaty tesing isn't about heat. It's about testing if the OC is stable or not. You will get random BSODs if the OC is not stable. Prime95 and AIDA64 are the easiest ways to check for stabilaty due the the amount of stress they put on the system.

Why prime95??
For examply: If I increase the overclock on my rig by 100mhz the PC will appear to run fine on the desktop but once I run Prime95 it will BSOD withing a few secs - 1 minute. Meaning it's running unstable.
is their any other way of telling if it unstable
Última edição por p0mpous; 21/set./2017 às 11:12
#15
< >
Exibindo comentários 1–15 de 44
Por página: 1530 50

Todas as discussões > Fóruns Steam > Hardware and Operating Systems > Detalhes do tópico
Publicado em: 21/set./2017 às 10:32
Mensagens: 44
Iniciar uma nova discussão

Regras e diretrizes para discussões