安装 Steam
登录
|
语言
繁體中文(繁体中文)
日本語(日语)
한국어(韩语)
ไทย(泰语)
български(保加利亚语)
Čeština(捷克语)
Dansk(丹麦语)
Deutsch(德语)
English(英语)
Español-España(西班牙语 - 西班牙)
Español - Latinoamérica(西班牙语 - 拉丁美洲)
Ελληνικά(希腊语)
Français(法语)
Italiano(意大利语)
Bahasa Indonesia(印度尼西亚语)
Magyar(匈牙利语)
Nederlands(荷兰语)
Norsk(挪威语)
Polski(波兰语)
Português(葡萄牙语 - 葡萄牙)
Português-Brasil(葡萄牙语 - 巴西)
Română(罗马尼亚语)
Русский(俄语)
Suomi(芬兰语)
Svenska(瑞典语)
Türkçe(土耳其语)
Tiếng Việt(越南语)
Українська(乌克兰语)
报告翻译问题
I only really find I need to use Rubbing Alcohol (91% is good, less water)
and an un-used paint brush; one with horse-hair perhaps, not cheap plastic bristles.
Easily found for cheap at WalMart or other places.
It is not that hard to take-apart and clean a controller, especially Xbox 360 / One types.
I also spray the internal thumb-stick regions with Silicon Spray; easily obtainable and cheap.
DO NOT use WD40 or similar sprays which can be harsh to sensitive electronics and plastics. A small can of such spray can last you years. Then once a small spray is applied to this area[www.image-tmart.com] take a moment to work the stick around in circluar motions all around in one direction, then back around in the opposite direction. Once done for both sticks, put the controller back together carefully. Silicon Spray is not conductive, so if you get a small run-off, not to worry, just clean that up with alcohol and dry that area using your brush.
For guides on disassembly you can find plenty here:
https://www.ifixit.com/Search?query=Xbox+360+Controller+
as well as on YouTube if you'd rather have a video based walk-through.
Here's an example of the silicon spray:
https://www.evike.com/search/?search_in_description=1&sort=3a&keywords=silicon+spray
If you are dealing with a wired controller, be mindful and careful of the wiring, it's much more fragile once you open the controller and thus release the area which holds that in-place, which can add some stress to the bare wiring itself.
If wireless, well those should be easier since it's just a plastic cap and then remove the batteries.
There is a Dead-Zone feature right within Steam BigPictureMode you can modify.
If you need to adjust this outside of Steam Client, then you will want this for Xbox Controllers > https://github.com/KrossX/Durazno and here is a tutorial for this app/input-wrapper > https://www.youtube.com/watch?v=DkkGT6myNbk
I had thrigh problem in one specific game for, but only for a day or two. It solved itself after a Steam update.
I don't even use Big Picture Mode for a controller because there's some bad bugs in it.
Solved: updating the Xbox 360 wireless receiver driver to version 2.1.0.1349, checking for files integrity and updating the nvidia drivers did the trick. I think the critical part was the controller driver, but I am really confused as to why that got buggy out of nowhere.
My controller would drift up every few minutes and could only be stopped by clicking the analog in. I asked Steam support, I asked Microsoft support, I got the Microsoft Accessories app to update firmware, and in short tried literally everything else I could think of. This fixed it. I hope it helps you!
Unfortunately I never did find a fix for it, one day Steam updated and everything worked just fine again, sorry I couldn't help, but I wish you luck in solving your issue.