Update

[diverbul]

Hi,

I just want to know for info when comes the update ?

I know you do your best I thank you

[Valen]

It's ready when it's ready. This hapens when you put a definite time mark on a schedule. Things come around that force you to delay. Let's just keep our patience.

[Valen]

And it is ready now!

[AllegPeet]

Update 0.20 is out. Number one tip: do not run out of compressed air!

[Playboy]

Depth Bot seems messed up.

You order him to go to periscope depth and the gauge says 10m and not the normal 12m and my UZO and RDF Loop and Guns are still above the waterline.

Also when i want to go to decks awash i usually go to 7m. This allows the Conning Tower to remain above the waterline. I told him to go to 7m and again he took me to 10m and i drowned.

[boris.glevrk]

Originally posted by Playboy:

Depth Bot seems messed up.

You order him to go to periscope depth and the gauge says 10m and not the normal 12m and my UZO and RDF Loop and Guns are still above the waterline.

Also when i want to go to decks awash i usually go to 7m. This allows the Conning Tower to remain above the waterline. I told him to go to 7m and again he took me to 10m and i drowned.

Perhaps you should manually set it at 11.

11 meter, if I remember correctly, allows the OP to be exposed, the original 12 doesn't.

When I was playing w/o bots I usually go to 14, though.

[Playboy]

Originally posted by boris.glevrk:

Originally posted by Playboy:

Depth Bot seems messed up.

You order him to go to periscope depth and the gauge says 10m and not the normal 12m and my UZO and RDF Loop and Guns are still above the waterline.

Also when i want to go to decks awash i usually go to 7m. This allows the Conning Tower to remain above the waterline. I told him to go to 7m and again he took me to 10m and i drowned.

Perhaps you should manually set it at 11.

Not much use having the Depth Bot if he can't get you to required depth. They've really screwed the pooch with this update in that respect. Hopefully patched soon.

[The_Mask]

Originally posted by Playboy:

Depth Bot seems messed up.

You order him to go to periscope depth and the gauge says 10m and not the normal 12m and my UZO and RDF Loop and Guns are still above the waterline.

Also when i want to go to decks awash i usually go to 7m. This allows the Conning Tower to remain above the waterline. I told him to go to 7m and again he took me to 10m and i drowned.

My sub goes to 12 mts the same as before .

[[ MARMITE ]]

Same here. Periscope depth at 12m and holding. Bot is still slowly losing it if full-stop, fair enough.
However I have "lost" deck awash depth.
I could run on diesel with deck awash through manual control in previous version. Now I only get a flooded diesel (7m) on manual or a switch to electric power if ordering the bot.
It could be me not handling the new buoyancy system properly... More testing needed.

Red

[WolfpackDevTeam_Einar]

Originally posted by Playboy:

Depth Bot seems messed up.

You order him to go to periscope depth and the gauge says 10m and not the normal 12m and my UZO and RDF Loop and Guns are still above the waterline.

Also when i want to go to decks awash i usually go to 7m. This allows the Conning Tower to remain above the waterline. I told him to go to 7m and again he took me to 10m and i drowned.

Hello! Does this occur when you give the bot a specific depth order without altering the trim tank or the plane rudders manually? Altering the trim tank or plane rudders manually overrides the previous order and makes the bot "stand down" until the bot is issued a new order. When a new order is issued the bot will automatically adjust the trim. We are working on making this more clear by having the bot tell you when it is active or not. I hope this helps. If not, please tell us and we'll figure it out.

[Dawg]

In my testing, the bot dive master cannot return the boat to a decks awash state after submerging. The only choice I have is to issue a surface command which completely empties the ballast tanks and fully exposes the sub. There seems to be a problem with bot depth control required for decks awash (6 to 7 meters).

[Playboy]

Originally posted by WolfpackDevTeam_Einar:

Originally posted by Playboy:

Depth Bot seems messed up.

You order him to go to periscope depth and the gauge says 10m and not the normal 12m and my UZO and RDF Loop and Guns are still above the waterline.

Also when i want to go to decks awash i usually go to 7m. This allows the Conning Tower to remain above the waterline. I told him to go to 7m and again he took me to 10m and i drowned.

Hello! Does this occur when you give the bot a specific depth order without altering the trim tank or the plane rudders manually? Altering the trim tank or plane rudders manually overrides the previous order and makes the bot "stand down" until the bot is issued a new order. When a new order is issued the bot will automatically adjust the trim. We are working on making this more clear by having the bot tell you when it is active or not. I hope this helps. If not, please tell us and we'll figure it out.

Sorry I missed this. The original issue was a couple of days ago and seems much improved since 0.20a released. However I used to go to decks awash at 7m and travel on the surface still using the diesels. Now at 7m the upper deck is flooded and I drown in rough sea's or have to order a very quick surface command if I can catch it in time.