Split 1 line into 6 lines

[John $ick]

Question in titel. Everyone know how it works?

[John $ick]

nvm, i already figuret it out:D after 1h :D

[Teh Freek]

First I split it into 3 (feed the fourth splitter output back to the initial input), and then split each of those into 2.

[KatherineOfSky]

This is where I go shopping for belt balancers:
https://www.reddit.com/r/factorio/comments/4d3per/belt_balancer_compendium/

[Warlord]

Автор сообщения: KatherineOfSky

This is where I go shopping for belt balancers:
https://www.reddit.com/r/factorio/comments/4d3per/belt_balancer_compendium/

I use this 4 lane balancer seen in the OP here: https://forums.factorio.com/viewtopic.php?f=8&t=9529
You can use any number of inputs or outputs to get what you want. 3 in 2 out? Use this balancer and hook up to the appropriate belts. Seems to come out balanced for me.

If I ever have to balance 8 belts, I think I'll just use 4 of these.

[Nailfoot]

Автор сообщения: Warlord

Автор сообщения: KatherineOfSky

This is where I go shopping for belt balancers:
https://www.reddit.com/r/factorio/comments/4d3per/belt_balancer_compendium/

I use this 4 lane balancer seen in the OP here: https://forums.factorio.com/viewtopic.php?f=8&t=9529
You can use any number of inputs or outputs to get what you want. 3 in 2 out? Use this balancer and hook up to the appropriate belts. Seems to come out balanced for me.

If I ever have to balance 8 belts, I think I'll just use 4 of these.

That is 4 too many splitters, though. You only need those middle 4 if you plan to pull a line of plates from one of them, and even then you can eliminate some.

EDIT

http://steamcommunity.com/sharedfiles/filedetails/?id=922470887

http://steamcommunity.com/sharedfiles/filedetails/?id=922471933

I think the design is from the old days when belt corners were not compressed so splitters were used. That's not been the case for sometime though.

[Nailfoot]

Автор сообщения: KatherineOfSky

This is where I go shopping for belt balancers:
https://www.reddit.com/r/factorio/comments/4d3per/belt_balancer_compendium/

I have the same site book marked. I wish the poster would edit the 4:4 though as the newer design is more straightforward, even though its a few tiles bigger.

[Dragorin]

Автор сообщения: KatherineOfSky

This is where I go shopping for belt balancers:
https://www.reddit.com/r/factorio/comments/4d3per/belt_balancer_compendium/

Thank you, I was going to go looking for belt balancers today to add to my growing blueprint book.

[Warlord]

Автор сообщения: Nailfoot

Автор сообщения: Warlord

I use this 4 lane balancer seen in the OP here: https://forums.factorio.com/viewtopic.php?f=8&t=9529
You can use any number of inputs or outputs to get what you want. 3 in 2 out? Use this balancer and hook up to the appropriate belts. Seems to come out balanced for me.

If I ever have to balance 8 belts, I think I'll just use 4 of these.

That is 4 too many splitters, though. You only need those middle 4 if you plan to pull a line of plates from one of them, and even then you can eliminate some.

EDIT

http://steamcommunity.com/sharedfiles/filedetails/?id=922470887

http://steamcommunity.com/sharedfiles/filedetails/?id=922471933

I think the design is from the old days when belt corners were not compressed so splitters were used. That's not been the case for sometime though.

Yeah, I use the one without the 4 splitters in the middle. I like the look of the one with the splitters, but it's way too much. I hadn't even realized that the devs fixed curves on belts uncompressing a line, I simply didn't care and used the line curves like you posted anyway.