Liftoff and radiolink AT9

[Haristobald]

Hi everybody,
I cannot make my radiolikn AT9 work with liftoff. It works well with fpv freerider!
it seems lift off recconize the right stick but not the left one?
do you guys have any idea of solution?

Thanks ;)

[typhoonfr]

Hi,
I plan to buy a radiolink AT 9. How do you connect this radio to a PC? Do you need a special cable?

[Haristobald]

I bought a mono jack-jack with adaptator on banggood at realy cheap price. With freerider fpv it works like a charm ;)

[typhoonfr]

Thank you :)

[76561198274994010]

Originally posted by Haristobald:

Hi everybody,
I cannot make my radiolikn AT9 work with liftoff. It works well with fpv freerider!
it seems lift off recconize the right stick but not the left one?
do you guys have any idea of solution?

Thanks ;)

I have an AT9 and the game will not recognize the throttle/left axis. Any suggestions?

[Haristobald]

yep same problem ;)

[pkendall64]

I have the same problem. Tried all different ways of configuring the damn thing and I can't get it to work.
After calibration each of the axes goes min/max continuously very quickly.

[pkendall64]

Ok, I got my radiolink at9 working! I followed instructions to that said configure using joystick, do the "Assign" first then the "Calibrate and Assign" and it worked. I found that moving the sticks during the individual calibration section in the direction when you press the button is best, i.e. before the stick is at it's full reach, then move them about.

I'm using a 22in1 USB Simulator dongle set to "G5-G7 above" setting. Make sure this is setup, plugged in and AT9 powered up before starting steam. Also, set you ranges to 100% min to 100% max and ELEV and THRO are set to reverse. All trims and sub-trims are at zero.

Hope this helps everyone.

[DeviousDude]

So how do you set your ranges to 100% as there are no options for that. I'm always about 25% short in getting 100% in any direction. Of course I cant arm.

[3y3l3sS]

hi, i´ve got the at9 too... my problem: In SmartPropoPlus he is "bouncing" between 3, 10 and 12 channels. i mean it works, but because of these bounces my copter is totally inflyable because there are some peaks on the different axes. so he is fliing left and right everytime one of these peaks appear. On the PC of my friend it works totally fine. any ideas?

[pkendall64]

Originally posted by Devious Dog:

So how do you set your ranges to 100% as there are no options for that. I'm always about 25% short in getting 100% in any direction. Of course I cant arm.

I used the endpoint option on the at9 and configured them all to 140/140 to get full travel in the game. Hope this helps.

[pkendall64]

Originally posted by 3y3l3sS:

hi, i´ve got the at9 too... my problem: In SmartPropoPlus he is "bouncing" between 3, 10 and 12 channels. i mean it works, but because of these bounces my copter is totally inflyable because there are some peaks on the different axes. so he is fliing left and right everytime one of these peaks appear. On the PC of my friend it works totally fine. any ideas?

I did notice that I had to do the calibration a couple of times. Also, If i recall correctly, I started liftoff with both sticks centered.

[Haristobald]

Originally posted by pkendall64:

Ok, I got my radiolink at9 working! I followed instructions to that said configure using joystick, do the "Assign" first then the "Calibrate and Assign" and it worked. I found that moving the sticks during the individual calibration section in the direction when you press the button is best, i.e. before the stick is at it's full reach, then move them about.

I'm using a 22in1 USB Simulator dongle set to "G5-G7 above" setting. Make sure this is setup, plugged in and AT9 powered up before starting steam. Also, set you ranges to 100% min to 100% max and ELEV and THRO are set to reverse. All trims and sub-trims are at zero.

Hope this helps everyone.

thanks a lot it worked ;)!

[[no] Yodadog]

Sorry for posting in this old thread, but my (new) AT9 won't register YAW/ROLL-axis at all. (Aneagle USB-dongle). Same dongle used to to work pretty good with my old Nine Eagles J6 Pro-controller.

In new versions of Liftoff I don't seem to have the same options to assign and the calibrate and assign.

[WestMinster]

Originally posted by 3y3l3sS:

hi, i´ve got the at9 too... my problem: In SmartPropoPlus he is "bouncing" between 3, 10 and 12 channels. i mean it works, but because of these bounces my copter is totally inflyable because there are some peaks on the different axes. so he is fliing left and right everytime one of these peaks appear. On the PC of my friend it works totally fine. any ideas?

I just connected my AT9 for the first time, i used the dongle, set it to the second position G5-G7 and did a assisted setup, worked great first time, (i followed all the info from the youtube video about using smart propo plus, but could not get the driver to install under windows 10). forget the microphone port setup as described in that video, just use the dongle plugged into the USB port.....