Kara Boga Request (Solved with an Answer)

[Xeous]

I am needing help i need to make him a 1 handed sword with >= 100 Cut & >= 50 pierce and i cant find a way am i missing something? any suggestions or knowledge of what works would help.

Here is how I finally got it to work for myself after several variations and attempts

Materials:
Ore Type: Khanka Ore
Handle Type: Snow Tree
Fuller Type: Hollow Ground
Quenching Type: Fire Potion

Weapon Parts:
Pommel 14
Guard 9
Blade 21 X 13
Blade Point 1

Weapon Curve:
Shape Penalty 0%
Cut Rate Bonus 32%
Pierce Rate Bonus: -32%

[Vertius]

I'll tell you how i went about it so you can improve the sword, because for me it took a few tries to get it within specs.


Ore Type- Khanka
Handle Type- Snow Tree
Fuller Type- Hollow Ground
Quenching Type- Fire Potion

Pommel- Pommel 8
Handle- 9x Handle Shape 0
Guard- Guard 9
Blade- 15x alternating between Blade 7 and Blade 8
Blade Point- 7

Weapon Curve
-Shape Penalty 0%
-Cut Rate Bonus 31%
-Pierce Rate Bonus -31%

Good luck!

[rooossone]

i was having trouble with it earlier, i was being lazy and my 100% slaves kept making the handle too long so it became a horse chopper, i got them to make it like 4 times before i realised as all the other stats were fine

[rooossone]

also this image might help.....


https://imgur.com/a/medieval-blacksmith-karaboga-one-handed-sword-pX7cX4F

Good luck!

[Xeous]

I legit made it exactly like said on the bp it shows 31 percent its all right but for some reason when i actually make it it ends up at 32 and makes it just ever so slightly not qualify

[GuardiaN]

Yeah I've tried going the Khanka route, but unless you're a master and can do it 100% completion, there's just no way the margins are too small to account for hammering jank.
Best way was to get enough rep to buy the northern blades (level 2) and just spam the 3 cutting piece to max. I don't know how you managed to do it.
After some finagling I managed to get the values but no way you can manage; here's a screenshot of the margins I could manage with khanka.
https://www.dropbox.com/scl/fi/hl5u3xfdajy32wdx0dbf6/Screenshot-2025-01-15-10.22.44.png?rlkey=aagd30t9yfuxl7xahe9sxusn9&dl=0

[Big_Krispy_nut]

i followed your build and got the stats but its a legendary weapon and he wont accept it. do you know how i can make it masterwork, i've made 8 swords for him.

[nenacu]

Originally posted by Big_Krispy_nut:

i followed your build and got the stats but its a legendary weapon and he wont accept it. do you know how i can make it masterwork, i've made 8 swords for him.

It will accept legendary, some other aspect of your offering is wrong.

[DeadHeadAlex]

You say to use Khankha ore but your image shows Gaurila?

[Truly_Tasty]

I found that that the Above replies got me close, but did not get me the correct blade.

i used:
Pommel 3
Handle Shape 0 x3
Guard 9
Blade 21 x15
Blade Point 1
Khanka Ore, Snow tree. Hollow Ground(fuller), & Fire Potion(quenching)

At a 95% overall quality, this setup achieved 104.3 Cut Rate & 64.8 Pierce Rate.
I hope this helps. It took me way to long to figure this out.

[DarkGrievous69]

Found that this works while giving you room for error:
Ore: Khankha
Handle type: Any type
Fuller Type: Hollow Ground
Quenching Type: Fire Potion
Pommel: 2
Handle: 0 x 6 (24cm)
Guard: 2
Blade: 29 x 15 (75cm)
Blade point: 7
Don't need to curve the blade but can bend it to give a bit more room for error.
(Straight blade gets Cut >= 111/ Pierce >= 116)
(Curve of 14% gets Cut >= 126/ Pierce >= 101)

Hope this helps.

[Feros]

Hey Guys! Thanks to all your suggestions, I manage to design another version of the sword:
Khanka Ore
Hollow Fuller
Ebony Tree
Fire Potion

Pommel 3
Handle 0 x 9
Guard 4
Blade 9 / 10 x13 (I personally start with 10 first then 9)
Blade 29 x 2 (consecutively at the tip of the sword before the Blade Point)
Blade Point 1