Store Page
DCS World Steam Edition
All Discussions Screenshots Artwork Broadcasts Videos News Guides Reviews

DCS World Steam Edition

Store Page
Soulstain Mar 27, 2014 @ 4:04pm
Throttle Issue in missions not training
Sorry for the noob question right off the bat. If I start any ot the training missions in the A10C, I have full throttle control. When I switch to missions, the throttle is locked forward and I have no control over it. Any suggestions as to what I'm overlooking?
< >
Showing 1-9 of 9 comments
fearlessfrog Mar 27, 2014 @ 4:43pm 
If it's a cold start then you could try nudge the throttles forward with:

Right Alt+Home for left engine, Right Ctrl+Home for right engine.

Either that or check to see if Options / Misc / Synchronize Cockpit Controls HOTAS is turned off.

You can use the Right Control + Enter key to bring up an in-game Axis viewer too.
#1
Soulstain Mar 28, 2014 @ 11:24am 
The problem doesn't happen when I'm in a training scenario. Do the whole start up process and throttle moves as it should. Exit out, touch nothing and enter a mission. Doesn't matter whether I'm a cold start or in the air, I will now have no control of the throttle and it is pushed all the way forward. I've tried missions, campaign and all the same. If I go back to training the throttle again works. Moving back and fourth as it's suppose to.
#2
Soulstain Mar 28, 2014 @ 11:25am 
The sycnchronize cockpit controls hotas is turned on as well.
#3
FeltHλt Mar 28, 2014 @ 12:08pm 
what controller u use?
#4
fearlessfrog Mar 28, 2014 @ 12:18pm 
Originally posted by Shrimpwall:
The sycnchronize cockpit controls hotas is turned on as well.

Try turning it off.
#5
Soulstain Mar 28, 2014 @ 1:22pm 
The new Saitek X55 HOTAS. Ok I appear to have gotten it working. I have the synchronize cockpit turned off. I will continue to play around with it and see if the problem is fixed across the board. I'm sorry for the questions but I'm just learning my way in DCS. Thanks for the help.
#6
Soulstain Mar 28, 2014 @ 1:23pm 
Not sure why it would always work in training but not actual missions though!
#7
FeltHλt Mar 28, 2014 @ 1:38pm 
check out official dcs forum, i found some probably interesting stuff, im not familiar enough with your case to judge :P but it wont hurt to look


http://forums.eagle.ru/index.php
Last edited by FeltHλt; Mar 28, 2014 @ 1:39pm
#8
fearlessfrog Mar 28, 2014 @ 2:05pm 
Originally posted by Shrimpwall:
The new Saitek X55 HOTAS. Ok I appear to have gotten it working. I have the synchronize cockpit turned off. I will continue to play around with it and see if the problem is fixed across the board. I'm sorry for the questions but I'm just learning my way in DCS. Thanks for the help.

No worries, plus glad you have it working better now.

The training mission may have a trigger set up to disable the auto sync of the controls, while actual missions won't. In the mission editor this is under triggers, set a mission start > no condition > prevent controls sync "on" trigger.

The autosync allows various HOTAS setups (like the TM Warthog) to set the in-game switches/setup to reflect how you have them set up on your device (sort of like an active pause for the cockpit). For the training missions they wanted that off I guess.

#9
< >
Showing 1-9 of 9 comments
Per page: 1530 50

DCS World Steam Edition > General Discussions > Topic Details
Date Posted: Mar 27, 2014 @ 4:04pm
Posts: 9

Discussions Rules and Guidelines