Unreachable welding seams in Zeppelin

[Pesky]

I've found two seams in Zeppelin which cannot be reached. There's just nowhere to stand that's close enough. And I have my suspicions on two more, but I haven't tried every possible standing-point yet.

Or did I already remove the platform I should be standing on ? Tell me whether you have the same problem.

[GeorgeSalton]

I found a weld point on a damaged hull beam that I could only get by grappling to the ceiling and swapping to the welder as I fell.
Another 2 I could get by standing on the damaged hull skin and jumping and the last 1 I grappled onto a bent beam next to it and crouched.

[Pesky]

I did the crouching one. But thanks for the tip which might help others.

But I'm on an old slow computer. My welding torch doesn't start welding while I'm in the air. It doesn't start fast enough to let me jump any distance and weld while I fall. :-(

There are also two welding strips near the curved walkway which are partially inside the hull. I managed to do both of them but it took me over 30 minutes of trying different angles, crouching, looking upwards, etc..

[sam <3]

If you have a place to stand, but it's too low and not close enough, I placed a mobile cargo and climbed onto it. Somehow it worked.

[Pesky]

I think most of them are fixed. There's still one on the starboard (right, east) hull where you have to stand on a 'tongue' stiicking out, and even then it's too far to reach with my welding torch. I never thought of sam's ingenious solution but I managed it in perhaps 30 attempts by jumping off of the tongue and welding as I fell. Most times I missed it entirely.

[+Арматур-Батыр+]

Originally posted by Pesky:

I think most of them are fixed. There's still one on the starboard (right, east) hull where you have to stand on a 'tongue' stiicking out, and even then it's too far to reach with my welding torch. I never thought of sam's ingenious solution but I managed it in perhaps 30 attempts by jumping off of the tongue and welding as I fell. Most times I missed it entirely.

that one is reachable from the outside. There is a small narrow opening there where you can reach the welding. Its tricky, but jumping and "fly-welding" is trickier

[Shawn]

I also completed by falling by with the cutter going. I didn’t think there would be a way to reach it from outside.

[MizMeow1]

Originally posted by +Арматур-Батыр+:

Originally posted by Pesky:

I think most of them are fixed. There's still one on the starboard (right, east) hull where you have to stand on a 'tongue' stiicking out, and even then it's too far to reach with my welding torch. I never thought of sam's ingenious solution but I managed it in perhaps 30 attempts by jumping off of the tongue and welding as I fell. Most times I missed it entirely.

that one is reachable from the outside. There is a small narrow opening there where you can reach the welding. Its tricky, but jumping and "fly-welding" is trickier

Thank you for this information. It worked!! The first time I worked on this ship, I couldn't get it and just ended up leaving it. I'm working on the ship for a second time now. I'm re-doing it mostly because of this one spot and also because I had lost one of the back pieces on my first time around. I disconnected a floor board and it was destroyed before I could get the crane to carry that part off. Anyway, two days ago, I spent nearly an hour trying to get the torch to completely destroy this area. I had tried jumping and crouching. All I could get was about 3/4 of it destroyed. I had tried looking at the outside, but didn't see a way to do it until you said that it *could* be done. You were right. There is one small spot you can *JUST* stand on to reach it from the outside. I had to crouch, but it worked. Thank you!